Skip to content

Damaged electrical wire: what to do straight away, and how we repair it

A drill bit through the wall, wires chewed in the cellar, insulation crumbling in an old flat: a damaged wire isn't fixed with insulating tape. Here's what to do straight away, and how we put the circuit right.

A damaged electrical wire isn't always visible. When it's been drilled in a wall, you can't tell whether it was grazed or half cut through. When it has overheated, the insulation may have melted over several centimetres inside the box. Either way, the risk is the same: a short circuit, a current leak, or heat building up unseen behind the plaster.

Straight away: switch off the circuit

If you've just drilled into a wire, there are two cases. If a breaker or the RCD tripped as you drilled, the bit touched a conductor: leave it off. If nothing tripped, the wire may still have been nicked, which you can't see. Switch off the circuit's breaker anyway, or the main breaker if you don't know which one it is. Once the power is off, pull out the bit, don't put a wall plug in and don't fill the hole: we need to be able to see what was hit.

Same reflex for wires chewed in a cellar or loft, or a wire that has blackened where it leaves a socket or a box: switch off the circuit and don't touch it again. Don't turn the power back on to a damaged wire, even if everything seems to work.

Sometimes you don't know where the problem is, but some signs should alert you: a smell of hot plastic, an RCD that keeps tripping for no obvious reason, a socket or a switch plate that feels warm.

What not to do

Insulating tape round a nicked wire, a terminal block hidden in the wall and then plastered over: we still come across them when we open walls, and that's exactly what to avoid. The wiring rules require connections to stay accessible, in a box with a cover. A joint buried in plaster eventually works loose and heats up, and nobody sees it.

How we repair it

It all depends on where the wire is damaged and the route it follows. Depending on the case, we choose one of these three solutions.

Replacing the wire from one box to the next

When the wire runs through a conduit, we try to pull a new one between the two boxes on either side, without opening the wall. It works when the conduit is in good condition and not too crowded, and you only find out by trying. It's the cleanest repair: no joint is left along the route.

An accessible box at the damaged point

When the wire can't be pulled through, we open the wall just around the damaged point and remake the connection in a junction box. It stays accessible: once the wall is made good, you see a small cover flush with the wall, which can be opened for checks.

A new route

When the old route can't be used, for example wires laid without conduit straight into the plaster, we run a new cable along another route: in a chase that we fill afterwards, in a skirting trunking or under a moulding. It's the same technique as for adding a socket.

A pierced or crushed conduit is dealt with the same way: we replace the wire inside it, and the damaged section of conduit where we can get to it.

Exposed wires: protecting them

A cable fixed at floor level, behind furniture or along a door frame ends up crushed or torn. Wires that stay exposed need protecting: trunking or a moulding along the wall, skirting trunking at the bottom, rigid conduit in a cellar where mice get through. And for the extension lead running across the room, the real fix is one more socket in the right place.

When the whole installation is ageing

In older buildings you still find rubber-insulated or cloth-covered wires whose insulation crumbles as soon as you move them. Repairing one wire, then another, solves nothing: the whole circuit needs redoing. We'll tell you when that's the case, and our page on old apartment rewiring explains how we go about it.

Drilling without hitting a wire

Buried cables normally run straight up, down or across from sockets, switches and light points. Avoid drilling in line with them, and switch off the circuit if in doubt. A cable detector helps, but it isn't foolproof in old walls.

What it costs

The diagnosis usually fits within our €132 incl. VAT call-out, travel and the first half-hour included: we find the damaged point and make the circuit safe. If we can't find the fault, we don't charge for the call-out. The repair depends on the wire's route and what needs opening up: we tell you the cost before starting. We fill the chases and openings; the painting is left to you.

Our prices are detailed on our call-out prices page, and for other faults, see our electrical repair page. To book a visit, contact us.

Request your free quote. Reply within 48h, detailed quote within a week.

Request a quote

Frequently asked questions

I've drilled into an electrical wire. What should I do?

Switch off the circuit's breaker, or the main breaker if you don't know which one. If a breaker tripped as you drilled, leave it off. Don't fill the hole, and have the wire checked before turning the power back on: a nick can't be seen.

Can you repair an electrical wire with insulating tape?

No. Tape insulates poorly, comes unstuck with heat, and the nicked wire stays weakened underneath. A proper repair means a new wire, or a connection remade in an accessible box.

Can a joint be made inside the wall?

Not a hidden one: the rules require connections to stay accessible. We can, however, fit a junction box at the damaged point, with a cover flush with the wall.

What should I do if mice have chewed the wires?

Switch off the circuit concerned and don't touch it again. We replace the chewed lengths and protect the wires in conduit where the mice get through. For the mice themselves, you'll need pest control.

How much does it cost to repair an electrical wire?

The diagnosis usually fits within our €132 incl. VAT call-out, travel and the first half-hour included. The price of the repair depends on the wire's route and what needs opening up: we tell you before starting.

Request a quote

Tell us about your project, we will get back to you shortly.

Thank you, we will reply shortly.
An error occurred. Please call us directly.
📞 06 70 54 03 91